Download Article

Download Article

If you beloved the wait of cuffed trousers, you can make your turn ups permanent by sewing the cuffs in place. You'll need to know your manner around a sewing machine to complete this project, just other than that requirement, information technology's a simple task that you can easily complete in an afternoon. Yous'll have those as well-long trousers transformed into a fashionable pair of plough ups in no fourth dimension!

  1. 1

    Put on the pants and the shoes you plan to wearable them with. This helps you lot get an accurate measurement. Make sure the pants are sitting on your waistline comfortably the way you normally article of clothing them. Otherwise, the length of your cuffs might exist off a niggling![1]

  2. 2

    Turn up the material to the length y'all desire and pin information technology in place. Fold the lesser of each pant leg up and look in the mirror to make sure the length looks fifty-fifty for both legs. So, pop a couple of pins around the border of each leg to hold the folded material in place.[2]

    • It wouldn't hurt to measure from the crotch seam downward to the new length and jot that measurement down. That way, you have backup measurements.[3]

    Ad

  3. 3

    Use a seam ripper to remove the original hem. Accept the pants off and work the seam ripper under each hem stitch to cutting the thread. So, unfold the hem so the textile hangs loose. Do the aforementioned thing for the other leg.[four]

    • A razor blade works if you don't accept a seam ripper handy.[5]

  4. 4

    Atomic number 26 the hems to get rid of the one-time creases. Identify the offset leg on an ironing board and gently printing the material until the old crease disappears. So, exercise the same for the other leg. Now you have a well-baked, fresh start to create new cuffs![6]

    • Old hem creases can be tough to get out! Effort using the steam function on your iron or a clothes steamer if the creases are being stubborn.

    Advertisement

  1. ane

    Stack the pant legs and lay them out apartment. Fold the pants on the creases like you lot were hanging them up. Then, lay them flat in front of you with the waist end on your left and the hem terminate on your correct. Shine the material with your hand.[7]

    • To make sure the pants are perfectly polish, take hold of the waist with your left hand and legs with your right hand and requite them a petty tug.

  2. 2

    Fold the legs up to the length you measured earlier and iron a crease. Catch the ends of both legs at the aforementioned time and fold them at the pin you lot used to marking the length. Accept the pin out, make sure the fabric is laying perfectly flat, and fe along the fold to mark the length with a crease.[viii]

    • Don't worry—since the legs are stacked, the fe volition crease both legs.

  3. iii

    Fold the legs down to create a 2 in (5.1 cm) cuff and iron again. Turn the ends of the pants downwards so the material goes slightly across the first crease. This creates a new fold about two in (5.1 cm) above the first pucker. Utilise an iron to press the new crease into your pants.[9]

    • You lot can make your cuffs smaller if you similar. 1 1⁄2  in (iii.8 cm) and 1 1⁄iv  in (three.ii cm) are both popular. Don't create cuffs larger than two 1⁄2  in (half dozen.four cm) though, since that tin look unbalanced![x]
    • If there's more than 1⁄2  in (ane.three cm) of excess material beyond the beginning crease, trim it down to 1⁄2  in (1.3 cm).

  4. 4

    Unfold the legs to the full length, invert the folds, and fe the ends. Split the legs to make sure the creases are crisp on both pant legs. Then, tuck the material inside the first leg then the stop of the pants stops at the first crease. Practise the same for the other leg. Run an iron along the end of each pant leg to printing the cloth in place.[11]

    • Now in that location is one visible crease and the excess fabric is tucked inside each pant leg.

    Advert

  1. 1

    Directly stitch along the visible crease from the inside of the pants. Thread your bobbin with matching thread and arrange the first leg nether the needle so you're stitching on the inside of the leg. Straight run up all the mode around the pant leg forth the visible crease. And so, do the same for the other leg.[12]

    • Stitch through ane layer of material at a time.
    • If it'southward tough for you to sew on the within of the legs, turn the legs inside-out and practise information technology that way.[13]

  2. 2

    Fold the material up until you hit the row of stitches and iron once again. Your turn ups are really taking shape now! Fold the finish of each leg up until you hit the new stitches; you won't be able to fold the cloth beyond this indicate. Use your iron to press this new fold into identify. Do the same matter for the other leg.[14]

    • Brand sure the side seams on the cuffs line upwards with the side seams on the legs before you fe each cuff.

  3. 3

    Straight sew beyond both side seams on each cuff. These last seam stitches will concur your gage in place! Simply sew a straight stitch across the inner and outer side seams for both legs. When you sew across the gage, sew right up the edge, but don't sew through the edge.[15]

  4. 4

    Press the cuffs a concluding time to create a crisp border. The hard office is over! At present, you just need to run your fe over both of your new cuffs to printing a clean, crisp border into your pant legs. The sharper the crease, the ameliorate your finished cuffs will look.[sixteen]

    Advertisement

Ask a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You lot'll Need

  • Thread
  • Scissors
  • Iron
  • Ironing board
  • Straight pins
  • Seam ripper
  • Sewing automobile

References

Most This Article

Thanks to all authors for creating a page that has been read 13,114 times.

Did this article help yous?